Sennheiser evolution wireless SR 300 IEM Bedienungsanleitung

SR 300 IEMInstruction manual

Putting the transmitter into operation8Putting the transmitter into operationPreparing the transmitter for useSetting up the transmitter on a flat sur

Putting the transmitter into operation9Connecting therod antennaThe supplied rod antenna  is suitable for use in good reception conditions.왘 Connect

Putting the transmitter into operation10왘 Connect the antenna. You have the following options:– You can connect the supplied rod antenna  to the rear

Putting the transmitter into operation11Connecting external devicesConnecting external devices to the input sockets왘 Use a suitable cable to connect t

Putting the transmitter into operation12Connecting transmitters in a networkYou can connect several transmitters in a network. The transmitters are re

Using the transmitter13Using the transmitterTo establish a transmission link, proceed as follows:1. Switch the transmitter on (see below).2. Switch th

Using the transmitter14To activate the RF signal:Monitoring the audio signal via headphonesYou can monitor the audio signal via the headphone output.

Using the transmitter15Carrying out an Easy Setup Sync or a Sync functionThe following assumes that you are using the Easy Setup Sync function for set

Using the transmitter16왘 Place the infra-red interface of thereceiver (see the instruction manual ofthe receiver) in front of the infra-redinterface 

Using the transmitter17Adjusting the audio channelsVia the “Mode” menu item, you can adjust the audio channels.왘 Select “Stereo” if you want to transm

Using the transmitter18Deactivating the lock mode temporarilyYou can activate or deactivate the automatic lock mode via the “Auto Lock” menu item. If

Using the operating menu19Using the operating menuThe buttonsButton Function of the buttonPress the STANDBY button• Switches the transmitter on and of

Using the operating menu20Overview of the operating menuWhen the standard display is shown on the display panel, you can get into the main menu bypres

Synchronizing the transmitter with a receiver21Synchronizing the transmitter with a receiverWhen synchronizing your transmitter with a receiver, pleas

Synchronizing the transmitter with a receiver22Synchronizing transmitters with receivers – multi-channel operationNetwork operationusing the WSMIn mul

Cleaning the transmitter23Cleaning the transmitter왘 Before cleaning, disconnect the device from the mains. 왘 Use a slightly damp cloth to clean the de

If a problem occurs ...24If a problem occurs that is not listed in the above table or if the problem cannot be solved with the proposed solutions,plea

Specifications25SpecificationsIn compliance with RF characteristicsFrequency ranges 516–558, 566–608, 626–668, 734–776, 780–822, 823–865 MHz (A to E,

Specifications26Approved byNT 2-3 mains unitIn compliance withThe mains unit is certified in accordance with the legal safety requirements of Europe,

Manufacturer Declarations27Manufacturer DeclarationsWarrantySennheiser electronic GmbH & Co. KG gives a warranty of 24 months on this product.For

Contents1ContentsImportant safety instructions ...

Sennheiser electronic GmbH & Co. KGAm Labor 1, 30900 Wedemark, Germanywww.sennheiser.comPrinted in GermanyPubl. 01/09529680/A01

Important safety instructions2Important safety instructions• Read this instruction manual.• Keep this instruction manual. Always include this instruct

Important safety instructions3Danger due to high volumesThis product is also intended for professional use. Commercial use is subject to the safety-at

The evolution wireless series ew 300 IEM G34The evolution wireless series ew 300 IEM G3This transmitter is part of the evolution wireless series gener

Delivery includes5Each frequency range (A–E, G) offers 26 frequency banks with up to 16 channels each:Each of the channels in the frequency banks “1”

Product overview6Product overviewOverview of the SR 300 IEM G3 transmitterABPUSHPUSHL(I)R(II)+22dBuMAXLoop OutBALL(I)R(II)BALAF IN+22dBu MAXRF OUT0682

Product overview7Overview of the displaysAfter switch-on, the transmitter displays the standard display.Display Meaning Audio level“AF IN L(I)” and “